Complete table of  Pomp's specifications
 

Model Min POWER INPUT at.Kw
150 bar 200 bar 250 bar 300 bar 350 bar 400 bar 500 bar 600 bar
R.P.M SHAFT
SIZE		 WEIGHT
Kg
PR 25 2.5 0.7 1 1.2 1.4 1.6 1.9 2.4 28 1450 17 12.6
PR 50 5 1.4 2 2.4 2.8 3.3 3.8 4.8 5.7 1450 17 12.6
PR 305 10 2.8 4 4.8 5.7 6.7 7.6 __ __ 1450 30 33
PR 308 17 4.9 6.8 8.1 9.6 11.4 13 __ __ 1450 30 33
PR 310 21 6 8.4 10 12.1 14.1 16.1 __ __ 1450 30 33
PR 508 28 8 11.3 13.4 16.1 18.8 __ __ __ 1450 30 39
PR 510 35 10 14.1 16.8 20.3 23.5 __ __ __ 1450 30 39
PR 512 42 12.1 16.9 23.1 24.2 28.2 __ __ __ 1450 30 39
PR 514 48 13.6 19.3 23 27.6 32.3 __ __ __ 1450 30 39
PR 712 59 17 23.8 28.3 34 39.7 __ __ __ 1450 34 42.5
PR 714 69 19.9 27.8 33.1 39.8 __ __ __ __ 1450 34 42.5
PR 714EX 67 25 35.1 41.8 __ __ __ __ __ 1450 34 42.5
AHP 195 32 9.2 12.9 15.1 18.4 __ __ __ __ 1000 35 24
AHP 205 36 10.3 14.5 17.1 20.7 __ __ __ __ 1000 35 24
AHP 197 45 12.9 18.1 21.6 25.9 __ __ __ __ 1000 35 24
AHP 207 50 14.4 20.1 24 __ __ __ __ __ 1000 35 24
AHP 199 58 16.7 23.4 27.8 __ __ __ __ __ 1000 35 24
AHP 209 64 18.4 25.5 30.7 __ __ __ __ __ 1000 35 24
AHP 1911 71 20.4 28.6 __ __ __ __ __ __ 1000 35 24
AHP 2011 79 22.7 31.9 __ __ __ __ __ __ 1000 35 24


Instructions for installation and starting

The hydraulic system must satisfy demands on pipe size, filtering, Etc. In accordance with size of pump input and also pump output installation The pump shaft may rotate in either direction.

1- Fit the section connection. Note the size of the section line that must be in accordance with pump input.

2- Fit the pump in any position of your choice.

3- Bleed the pump before starting it: AHP and PR 25-50 loosen the uppermost of the  bleed screws by 2-3 turns. PR pumps: fill up pump from the oil before starting.

Starting:

1- Run the pump without load for a minute or so, preferably at full speed, if the equipment works unevenly, there is still some air in the system.

Stop and start the pump a few times to bleed the system. Note,